Panel-Ready Appliances: A Planning Guide
On this page
Panel-ready appliances ship without a finished front, so your cabinet maker builds panels that match the cabinets and the refrigerator, dishwasher, and drawers read as part of the run. Planning them comes down to four numbers for each appliance (opening size, panel weight, panel thickness, and reveal), and to getting every maker's spec sheet to the cabinet maker before the cabinet boxes are drawn.
| Category | Examples from makers we carry | What the maker limits |
|---|---|---|
| Column refrigeration | Sub-Zero Designer, Thermador Freedom, Gaggenau Vario 400 | panel weight per door, panel thickness, cutout depth |
| Dishwashers | Cove, Bosch, Miele, Fisher & Paykel | panel weight range, minimum thickness, opening width |
| Refrigerator and freezer drawers | Sub-Zero Designer drawers | weight per drawer panel |
| Hood liners | Wolf Pro Hood Liner | how the liner meets the decorative hood |
Which appliances can take a cabinet front
Column and built-in refrigeration is where panel-ready planning starts, because the panels are tall and heavy; start with the column and built-in refrigeration we carry. Sub-Zero builds its Designer columns and tall units to take custom panels, and Thermador's Freedom columns and Gaggenau's Vario 400 columns are designed for a decorative door panel as well. For a side-by-side look at the formats, see our guide to comparing panel-ready refrigerator formats. Fisher & Paykel also builds integrated column refrigeration; ask us for the current panel spec for the model you're considering.
Dishwashers sit inside the base cabinet run, where a front that doesn't match is easy to spot. Cove, Bosch, and Miele each publish their own panel rules, and Fisher & Paykel builds integrated dishwashers and DishDrawer models that take a cabinetry panel.
Undercounter refrigeration and freezer drawers let an island or a beverage area disappear. Sub-Zero lists Designer drawer openings in 24-, 27-, 30-, and 36-inch widths, each 34 1/2 inches high. The undercounter refrigerator guide covers the formats.
Hood liners work the other way around. The cabinet maker or a finish trade builds the hood, and the appliance hides inside it. Wolf says the decorative hood around its Pro Hood Liner can be wood, plaster, tile, or metal, that the shape isn't critical, and that the liner and hood must meet at the bottom edge in both width and depth. Wolf also says the liner's bottom edge should not extend more than 3/4 inch below the decorative hood, and that the hood belongs 30 to 36 inches above the countertop. Our range hood guide covers sizing and airflow, and our page on hood liners and the ventilation lines we carry lists the makers.
Ovens, ranges, hoods, and warming drawers
Panel-ready planning reaches past refrigeration and dishwashers, so here is what the makers' documents in this guide say about cooking appliances. Wolf's Pro Hood Liner hides inside a decorative hood. Thermador's planning guide lists a Custom Panel Warming Drawer that requires a custom front panel, and says the panel must have a handle, a minimum thickness of 3/4 inch (19 mm), all edges finished, a sealed back if it is wood, and the ability to withstand 158 degrees Fahrenheit (70 degrees Celsius). Thermador says its warming drawers can sit below its single or double built-in ovens.
None of the maker documents used here describe a panel-ready wall oven, speed oven, range, or dryer, so this guide does not assume one exists. If you have one in mind, ask us whether the maker lists a panel-ready version of the exact model, and draw your cabinets around the appliance's own door and finish options until you have that answer in writing.
Panel weight sets the hinge
Every maker sets a maximum panel weight for each door or drawer. Go over it and you invite the problems makers warn about; Cove, for one, caps its panel at 20 pounds but says that above 16 pounds the door can no longer be balanced and may fall open. Ask your cabinet maker for the finished weight of each panel, including the handle, before anything is ordered.
- Sub-Zero Designer sets a separate limit for each column width, tall door and drawer; our built-in refrigerator installation steps list them.
- Thermador Freedom columns 121 pounds for an 18-inch freezer column, 90 pounds for a 24-inch, 93 pounds for a 30-inch, and 84 pounds for a 36-inch freezer or fresh food column. Ice and water dispenser columns list 159 pounds at 18 inches and 152 pounds at 24 inches.
- Gaggenau Vario 400 The 30-inch RC 472 705 refrigerator lists a maximum door panel weight of 53 pounds (24 kg).
- Dishwashers carry far lighter panels, and each maker sets its own range; the panel-ready dishwasher guide compares them side by side.
Weight doesn't always rise with width, so read the table for your exact model. In Thermador's chart, the 36-inch column allows less panel weight than the 24- or 30-inch.
Thickness and cutout depth
Panel thickness changes how far the door sits from the cabinet face, so it has to be settled together with the depth of the opening.
- Sub-Zero requires a panel at least 5/8 inch thick. Thicker is fine as long as the panel stays under the weight limit, but above 1 inch Sub-Zero says the 90-degree door stop may be needed to protect the unit and nearby cabinetry. Each Designer model is 24 inches deep, so the finished opening depth has to allow for the panel.
- Thermador bases its Freedom panel dimensions on a 3/4-inch panel and generally recommends a 25-inch-deep cutout with standard 3/4-inch panels. Its planning guide explains why: in a face-frame kitchen with standard overlay doors, matching the look of the frame can mean a panel built up to 1 1/2 inches, which needs the extra depth. Thermador says European-style frameless cabinetry can use a 24-inch cutout, and a framed install with its FRAMEKIT30 frame uses a 24-inch cutout.
- Dishwashers take thinner panels; check the minimum on each maker's template.
If your cabinets are inset or full overlay, tell us early. The door style decides the panel build, and the panel build decides the cutout.
Reveals, hinges, and finished backs
A reveal is the gap between a panel and its neighbors. Sub-Zero calls 1/8-inch reveals typical and warns that tighter ones can cause severe finger pinching as the door closes. Thermador designs its Freedom panel dimensions around 1/8-inch (3 mm) reveals, a 4-inch toe kick, and an 84-inch cutout height.
Hinges differ more than most people expect, and they decide how the door clears an island or a wall.
- Sub-Zero builds a 105-degree stop into the hinges of its tall and column models and supplies 90-degree clips to limit the swing.
- Gaggenau lists a flat hinge on the RC 472 705, with a door that opens to 115 degrees and can be fixed at 90.
- Thermador says its Freedom Hinge "enables true flush design," and the T36IR905SP column adds Auto Door Opening, which opens the door with a slight push or pull.
Panels show from the back when the door is open. Sub-Zero says to finish all sides, and Thermador says to finish the panel reverse to match the exterior. Cove asks the same for its dishwasher panels.
Panel-ready fit table by model family
| Model family | Opening (width x height x depth) | Panel weight limit | Panel thickness | Toe kick and door notes |
|---|---|---|---|---|
| Sub-Zero Designer columns 18, 24, 30, and 36 inch | See the maker installation guide | Set per model in the Sub-Zero Design Guide. The limit counts the whole panel, backer and spacer included, and the custom handle. | Maker stainless accessory panels are 3/4 inch thick. Custom panel thickness: see the maker installation guide. | Stainless panels are sized for a 4 inch or 6 inch toe kick, 79 7/8 or 77 7/8 inches high, with 1/8 inch reveals. |
| Sub-Zero Designer undercounter DEU, 24 inch | Depth 23 1/8 inches, plus panel thickness. Width and height: see the maker installation guide. | 22 lb (10 kg) maximum for 24 inch units, handle included. | 5/8 inch minimum, 3/4 inch maximum. | Standard panels fit a 4 inch toe kick. Minimum 1/8 inch reveals. Panels thicker than 3/4 inch interfere with the door opening. |
| Cove Dishwasher | See the maker design guide | 20 lb (9 kg) maximum. Under 16 lb (7 kg) is optimal. | 1/2 inch minimum. Thicker is allowed within the weight limit. | Panel at least 28 inches high; maker does not recommend over 30 3/8 inches. Template fits 23 3/8 inch and 23 3/4 inch wide panels. |
| Gaggenau Vario 400 RC 472 705 30 inch | See the maker specification sheet | 53 lb (24 kg) maximum door panel weight. | See the maker specification sheet | Flat hinge. The door opens to 115 degrees and can be fixed at 90 degrees. |
| Thermador Freedom columns | See the maker installation guide | See the maker installation guide | See the maker installation guide | See the maker installation guide |
| Bosch Custom panel dishwashers 100, 300, 800, and Benchmark | See the maker installation guide | See the maker installation guide | See the maker installation guide | Bosch lists these models as custom panel ready. Toe kick notes: see the maker guide. |
| Fisher & Paykel Integrated models Dishwashers and columns | See the maker installation guide | See the maker installation guide | See the maker installation guide | Fisher & Paykel lists these models as panel ready. Toe kick and door notes: see the maker guide. |
Figures are the makers' own, read from the pages listed under this table. Where a maker states a figure only in an installation or design guide, the cell points to that guide.
Sources for the fit table
- Sub-Zero Designer Series Stainless Steel Panel Dimensions
- Sub-Zero Designer Stainless Steel Panel Thickness
- Sub-Zero Maximum Panel Weight
- Sub-Zero Designer installation guide (PDF)
- Sub-Zero Designer Undercounter Stainless Steel Door Panels
- Cove Dishwasher Custom Door Panel Mounting
- Cove Dishwasher Custom Panel Weight Limit
- Cove Design Guide (PDF)
- Gaggenau 400 series Vario refrigerator 30 inch RC 472 705
- Gaggenau RC 472 705 specification sheet (PDF)
- Thermador Refrigeration Planning and Installation Guide (PDF)
- Bosch custom panel dishwashers (100, 300, 800, and Benchmark series)
- Bosch custom panel installation template (PDF)
- Fisher & Paykel integrated dishwashers
- Fisher & Paykel integrated cooling
The order the drawings change hands
Panel-ready kitchens go wrong when the cabinets are drawn before the appliances are chosen. This sequence keeps the cabinet maker and the appliance side working from the same numbers.
- Choose the models first.
Opening sizes, panel weights, and cutout depths come from the exact model number, not the category.
- Pull the spec sheets and installation guides.
We gather the current documents for every panel-ready appliance in the kitchen, plus panel templates where the maker publishes one. Cove lists its dishwasher template as part number 828042, and Bosch publishes a custom panel installation template.
- The cabinet maker draws the openings and panels.
Shop drawings should show each opening's width, height, and depth, each panel's size, thickness, and weight, the reveals, and the toe kick height.
- Check the drawings against the spec sheets.
This is where an opening that's 1/4 inch short, or a door that hits an island, gets caught on paper.
- Rough-in.
A licensed electrician and plumber place the outlets and water lines where each guide shows them, and your local building department sets what has to be inspected.
- Set the appliances, then hang the panels.
Sub-Zero's guide covers placement and alignment before panel installation, and Bosch says to attach its mounting brackets only after a fully integrated panel is on the door.
Building every panel to the appliance makers' numbers is the cabinet maker's job, so cabinetry planned around a full set of panel-ready appliances at a custom shop such as DreamLine Custom Cabinetry starts with all of those spec sheets in one folder. When the panels are ready, see delivery and installation for a paneled kitchen.
Questions to ask in the showroom
- What is the maximum panel weight for each model, and what will my panels weigh with handles?
- Does my door style need a 24-inch or a 25-inch cutout depth?
- What reveal does each maker design for, and will my cabinets match it?
- Where does each door stop when open, and does it clear the island?
- Which appliances have a panel template, and has my cabinet maker received it?
- Where do the outlets and water lines need to be before the cabinets go in?
Next steps in the Sacramento area
Start with kitchen appliances for Sacramento-area projects, then bring your cabinet drawings, door style, and the list of appliances you want paneled to the Roseville showroom. We'll pull the spec sheets and panel limits for each model with you so your cabinet maker has the numbers before the first cut. For the rest of the kitchen, browse our guides for the rest of the kitchen.
Updated