Workstation Sink Guide
On this page
A workstation sink is a sink with ledges built into the basin walls, so cutting boards, racks, colanders, and bowls can sit over the water and slide along it. That turns the sink into a second countertop. To choose one, size it to the base cabinet, decide which accessories you'll use, check that the faucet reaches the whole length, and pick the material.
| Model | Sink length | Minimum base cabinet | Ledges | Material |
|---|---|---|---|---|
| Kohler Prolific K-23651 | 29 in | 33 in on the technical drawing | three graduated ledges | 18-gauge stainless |
| Kohler Prolific K-5540 | 33 in | 36 in | three graduated ledges | 18-gauge stainless |
| The Galley Ideal Workstation 3S | 33 1/2 in outside | 36 in | multi-tiered | 16-gauge 316L stainless |
| The Galley Ideal Workstation 4S | 45 1/2 in outside | 48 in | three tier design | 16-gauge 316L stainless |
| The Galley Ideal Workstation 7S | 81 1/2 in outside | 84 in | multi-tiered | 16-gauge 316L stainless |
A second countertop over the basin
In an ordinary sink, the basin is dead space while you prep. In a workstation sink, a cutting board bridges the basin, a colander drains into it, and scraps go straight down the drain. You can chop on one end and rinse on the other without moving to the counter. Size it like counter space, not like a sink. If the island or perimeter run is tight on prep room, a longer workstation can give some of it back.
That also means the sink sets the size of the base cabinet below it, and the base cabinet is decided early in the kitchen drawings.

When a workstation sink earns its place
A workstation sink earns its place when prep space is tight or when you'd use the accessories every day: chopping over the basin, draining into a colander, rinsing without moving. If you rarely prep at the sink, a standard undermount sink with a separate cutting board does the same job with a narrower base cabinet.
Size it to the base cabinet
The right size is the longest sink your base cabinet allows: a 36-inch base takes a 33-inch Kohler Prolific or The Galley's 3-foot 3S, and a 48-inch base takes The Galley's 4-foot 4S. Every maker publishes a minimum base cabinet width for each model. Start there.
- Kohler lists a 36-inch minimum base cabinet for its 33-inch Prolific K-5540. For the 29-inch Prolific K-23651, the spec sheet's feature list gives 30 to 33 inches and says 30 may require cabinet modifications, while its technical drawing lists 33 inches. Plan for 33.
- The Galley lists a 36-inch minimum cabinet for its 3-foot Ideal Workstation 3S, 48 inches for the 4-foot 4S, and 84 inches for the 7-foot 7S. Its workstations run from 2 to 7 feet, plus corner configurations.
Both are undermount sinks. Kohler says the countertop fabricator must use the cut-out template that comes with the sink, and the K-23651 sheet lists that template as required and included. The Galley's 4S sheet gives a countertop cutout of 44 1/2 by 18 inches with a 1/2-inch reveal front and back. Get the template to your fabricator before the stone is cut.
If you're replacing a sink in an existing kitchen, measure the base cabinet's inside width first and choose second. A sink that needs a wider cabinet than you have means new cabinetry.
Ledges and the accessory kit
The ledges are what make the sink a workstation. Kohler's Prolific sinks have three graduated ledges in the basin so you can set accessories at different heights, and the accessories stack and slide along them. The Galley's 4S sheet lists a three tier design.
What comes in the box differs by maker and size.
- Kohler Prolific includes a bamboo cutting board, two multipurpose grated racks, a colander, and a wash bin. The included board is 10 by 16 inches and covers about a third of the sink. Kohler also offers a large 21 by 16-inch board that covers about two thirds of the K-5540.
- The Galley Ideal Workstation 4S includes what The Galley counts as five culinary tools: an Upper Deck section, an upper tier drying rack, an upper tier cutting board, two lower tier platforms, a stainless colander, and a stainless mixing bowl. The 7S includes eight. The Galley offers boards and decks in American black walnut, quartered white oak, graphite wood composite, and white or gray resin.
Check your countertop thickness against the accessories. The Galley's 4S sheet says its Upper Deck needs 1/4 inch of room below the countertop surface, and that with a countertop 3/4 inch thick or less, walnut or white oak Upper Deck sections won't have room to work above the upper tier tools. Tell your fabricator which accessories you plan to use before the counter is templated.
Faucet reach and how many cooks
A long basin needs a faucet that reaches its ends. The Galley recommends one faucet for its 4-foot 4S, rated for one user, and two faucets for its 7-foot 7S, rated for one to three users. Whatever you choose, confirm the spout reaches past the ledge accessories to the far corners of the bowl, and that the faucet's height clears a colander sitting on the upper ledge.
Kohler is one of our brand partners, and its sinks and faucets are on the line card and available to order.
Materials and gauge
Gauge is a thickness number, and a lower gauge is thicker steel. Kohler builds its Prolific sinks from 18-gauge stainless. The Galley uses 16-gauge 316L stainless, which it calls marine grade, and its 4S sheet rates the basin for indoor and outdoor use. The Galley says each basin is hand-crafted in the USA and wrapped in what it calls Sound Reduction Technology, which it says reduces noise and vibration by up to 95%.
Bowl depth matters for big pots and for how far you reach down. Kohler's technical data lists a 10-inch bowl depth for both Prolific models (the K-5540 feature list says 11 inches), and describes a beveled, cone-shaped bowl that slopes into the drain so debris clears easily. The Galley's 4S sheet lists interior dimensions of 44 by 17 by 10 inches.
Compare usable length, too, since the outside size includes the rim. Kohler's 29-inch K-23651 lists a bowl area 27 1/2 inches long, and its 33-inch K-5540 lists 31 1/2 inches. The Galley's 4-foot 4S lists a basin area of 44 by 16 inches.
Drains and the parts that come separately
Plan the drain with the plumber before the cabinet is built.
- Kohler lists the drain with strainer as a separate item for the K-23651, and for the K-5540 it lists either a disposal flange with stopper (K-11352) or a drain and strainer with tailpiece (K-8801) as required.
- The Galley uses a reversible side drain on the 4S and includes a drain cover. Ask where the drain lands relative to a disposal or pull-out bins.
A licensed plumber should confirm the drain, the disposal, and the water supply against your local building department's requirements.
The dishwasher usually sits right beside the sink base, so draw the two openings together; our guides to choosing a panel-ready dishwasher for the same cabinet run and a dishwasher review that covers panel kits cover that side.
Questions to ask in the showroom
- How wide is my base cabinet inside, and which sink lengths fit it?
- Which accessories come with this model, and which do I need to add?
- Is my countertop thick enough for the accessories I want?
- Does one faucet reach both ends, or do I need two?
- Where does the drain sit, and what does that leave for a disposal or bins?
- Who holds the cut-out template, and when does the fabricator need it?
Next steps in the Sacramento area
Bring your cabinet drawings, countertop thickness, and faucet plan to the Roseville showroom, and we'll pull the current spec sheets for The Galley and Kohler with you before anything is ordered. To see Kohler sinks in a finished island, visit Kohler sinks set into a finished island at Design Gallery. For the appliances around the sink, see more kitchen planning guides.
Updated